Select a six channel mixer Note:
A. Works according to the spiral belt mixer for mixing the mixed double helix with the ability to push the material in the opposite direction should be basically the same. Within the spiral with the pitch should be less than the outer spiral bands, to achieve the ability to push material consistent inner spiral with the pitch should be less than the outer spiral bands, the width should be larger than the outer spiral band, otherwise it would focus on the material in one direction . Therefore, in the choice of channel mixer to pay attention to this point.
Two. The gap between the design principles, channel mixer, spiral band and the shell can be 4 mm to 10 mm, the material can be mixed friction driven by all participants. However, due to the friction coefficient is not the same granularity and materials, make the various components of the materials to participate in mixing time is not the same, resulting in the heterogeneity of the product. Some manufacturers have been aware of this and the product has been improved. Attention to the machining accuracy, the end of the gap reduced to 1 mm to 2 mm; another spiral belt between the spindle and the shell made of a position adjustable, can be regularly adjusted according to the amount of wear between the shell the gap. Select the channel mixer, the product of these two forms is the best option.
3. Use the channel mixer to pay attention to the order of feeding. Generally vote aniseed, jade, rice flour, soybean powder, and then cast the group sub-material, such as premix. Note premix must not spiral elevator feeding the application of one-off tipping bucket feeding or artificial feeding, to avoid the segregation of the active ingredient in the premix loss.
4. Select the channel mixer to pay attention to a material way. Should choose the form of a large door, do not choose the side of the mouth or small opening at the bottom of the material in the form. The reason is: mixer mixing completed in a specified time, the shortest possible time once put clear to ensure material uniformity; such as opening side of the mouth or bottom of the spiral band gradually put the net, one delay time, up less than expected productivity, material already achieve the best uniformity, excessive mixing but will make the material segregation and undermine the uniformity, and thus lose the significance of selected channel mixer.
5 Use the channel mixer, should start in the mixer and then batch by batch feeding. Mixed end to the discharge and do not stop out of the net material and then mixed batch. If the full load and then start, will cause the power away from too much and burning motor.
6. According to the daily production of the selection of horizontal mixing machine. Due to the mixer each batch of material and processing time of about 6 minutes, with the materials and the feed time, processing time of each batch of material can be 10 minutes, one hour can be processed six batches of material. If you choose each batch processing capacity of 100 kg, channel mixer, then the process 600 kg per hour. The user can be selected according to their needs the channel mixer.
In short, choose an applicable channel mixer and used properly, will significantly improve the quality of its ingredients, and will soon reflect the benign effect in the breeding process. If you can master with premix technology, but also greatly reduce the cost of feed, and thus improve the profits of farming.
The safe use of a few key points of the universal grinder
Should be a universal grinder start idle 2-3 minutes, without exception after feeding.
2, universal grinder after installation to check the various components of the fastening at the same time to check the belt tightness is appropriate, whether the motor shaft and universal grinder shaft parallel.
3, universal before the start of the grinder, first hand rotation of the rotor, check whether the operation of normal flexible chassis and whether the collision phenomenon, the correct direction of rotation of the rotor, good motor and universal grinder lubrication.
4, on closer inspection of material, to avoid metals, stones and other hard objects into the crushing chamber to cause the accident.
Feeding, the staff should stand universal grinder side, wounded face to prevent the rebound out of the debris. Crushed long stalk hand can not grasp too tight to prevent hands being brought into.
Do not replace the pulley to prevent the speed is too high or too low.
Feeding, stop stop, stand inside the material rule out clean, then cut off the power shutdown. After the shutdown for cleaning and maintenance.
8, 300 hours after the universal grinder job to be cleaning bearings, change the oil; installed oil to full bearing gap of 1/3 as well, should not exceed a maximum of 1/2. Downtime, you should remove the belt.
Universal grinder should be fixed in the cement foundation. Such as frequent changes in the workplace, universal grinder and electric motors to be installed on the base made with angle.
10, the feed should be uniform, found noises, bearings, and the body temperature is too high or outward spray of material phenomena, should immediately stop inspection, troubleshooting. |
Purchase of the main points of the groove mixer and universal grinder should pay attention to